Jetting for Vortex KZ Kart PC 용 : 무료 다운로드

★ ★ ★ 에디터의 리뷰

1. Jetting for Vortex RVS, RVX, RVXX, RVZ, RKZ, RSZ, RTZ & VTZ is an application which provides, for the current weather conditions and a given engine configuration (engine model, carburetor, floats, track shape, etc.), a jetting recommendation for go-karts with Vortex RVS, RVX, RVXX, RVZ, RKZ, RSZ, RTZ and VTZ engines (ICC / KZ1 / KZ2 karting engines).

2. In order to get the weather values, the application can use the GPS to obtain the position and altitude, and the network connection to get the temperature, pressure and humidity from the nearest weather station.

3. - GPS: this tab allows to use the GPS to get the current position and altitude, and connect to an external service to get the weather conditions of the nearest weather station (temperature, pressure and humidity).

4. The values of this screen can be manually set or can be loaded by the application reading the data from the nearest weather station (from the GPS tab).

5. - Engine: you should set in this screen the information about the engine and the carburator (Dellorto VHSH 30 / PHBE 30), that is, the engine model (Vortex RVS, RVXX, RVX, RVZ, RKZ, RSZ, RTZ and VTZ), the float type and height, the oil mix ratio and the type of the circuit (sprint or road racing, short or long).

6. These data are calculated depending on the weather conditions and the engine and track configuration given in the following tabs.

7. The following carb values are given: main jet, emulsion tube, needle type and clip position, inner pilot jet (iddle diffuser) and outer pilot jet (iddle jet).

8. Nevertheless, the application can run without GPS and internet connection, in this case, the user must give the weather data.

9. - Weather: you can set the values for current temperature, pressure, altitude and humidity.

10. In addition, this tab lets do a fine tunning adjustment for the main (high) and needle (mid) circuits to adapt to the concrete engine.

11. The application works with different measure units: inHg, mb, mmHg, hPa, atm for pressure, ºC and ºF for temperature.

스크린 샷

다운로드 및 설치 방법 Jetting for Vortex KZ Kart 귀하의 PC 및 Mac에서

호환되는 PC 앱 또는 대안 확인

앱	다운로드	평점	개발자
Jetting	앱 또는 대안 다운로드 ↲	0 1	ISEnet

또는 아래 가이드를 따라 PC에서 사용하십시오. :

PC 버전 선택:

Windows 10
Windows 11

소프트웨어 설치 요구 사항:

1 단계 : PC 및 Mac 용 Android 에뮬레이터 다운로드

직접 다운로드 가능합니다. 아래 다운로드 :

2 단계 : PC 또는 Mac에 에뮬레이터 설치

3 단계 : Jetting for Vortex KZ Kart PC의 경우 - Windows 7/8 / 10 / 11

설치 한 에뮬레이터 애플리케이션을 열고 검색 창을 찾으십시오. 일단 찾았 으면 Jetting for Vortex KZ Kart 검색 막대에서 검색을 누릅니다. 클릭 Jetting for Vortex KZ Kart응용 프로그램 아이콘. 의 창 Jetting for Vortex KZ Kart Play 스토어 또는 앱 스토어의 스토어가 열리면 에뮬레이터 애플리케이션에 스토어가 표시됩니다. Install 버튼을 누르면 iPhone 또는 Android 기기 에서처럼 애플리케이션이 다운로드되기 시작합니다. 이제 우리는 모두 끝났습니다.
"모든 앱 "아이콘이 표시됩니다.
클릭하면 설치된 모든 응용 프로그램이 포함 된 페이지로 이동합니다.
당신은 아이콘을 클릭하십시오. 그것을 클릭하고 응용 프로그램 사용을 시작하십시오.

PC 용 호환 APK 받기

다운로드	개발자	평점	현재 버전
다운로드 PC 용 APK »	ISEnet	1	1.2

다운로드 Jetting Mac OS의 경우 (Apple)

다운로드	개발자	리뷰	평점
$7.99 Mac OS의 경우	ISEnet	0	1

기능 및 설명

Jetting for Vortex RVS, RVX, RVXX, RVZ, RKZ, RSZ, RTZ & VTZ is an application which provides, for the current weather conditions and a given engine configuration (engine model, carburetor, floats, track shape, etc.), a jetting recommendation for go-karts with Vortex RVS, RVX, RVXX, RVZ, RKZ, RSZ, RTZ and VTZ engines (ICC / KZ1 / KZ2 karting engines). In order to get the weather values, the application can use the GPS to obtain the position and altitude, and the network connection to get the temperature, pressure and humidity from the nearest weather station. Nevertheless, the application can run without GPS and internet connection, in this case, the user must give the weather data. The application is made up of four tabs that are described next: - Results: in this tab, a recommended jetting setup is shown. These data are calculated depending on the weather conditions and the engine and track configuration given in the following tabs. The following carb values are given: main jet, emulsion tube, needle type and clip position, inner pilot jet (iddle diffuser) and outer pilot jet (iddle jet). In addition, this tab lets do a fine tunning adjustment for the main (high) and needle (mid) circuits to adapt to the concrete engine. - Weather: you can set the values for current temperature, pressure, altitude and humidity. The values of this screen can be manually set or can be loaded by the application reading the data from the nearest weather station (from the GPS tab). - Engine: you should set in this screen the information about the engine and the carburator (Dellorto VHSH 30 / PHBE 30), that is, the engine model (Vortex RVS, RVXX, RVX, RVZ, RKZ, RSZ, RTZ and VTZ), the float type and height, the oil mix ratio and the type of the circuit (sprint or road racing, short or long). Depending of the track type, the jetting setups will be adapted. - GPS: this tab allows to use the GPS to get the current position and altitude, and connect to an external service to get the weather conditions of the nearest weather station (temperature, pressure and humidity). The application works with different measure units: inHg, mb, mmHg, hPa, atm for pressure, ºC and ºF for temperature.

다운로드 Jetting PC 용