다운로드 Electronics Tools PC 용

PC를 설정하고 Windows 11에서 Electronics Tools 앱을 다운로드하는 단계:

1. 컴퓨터가 호환되는지 확인: 최소 요구 사항은 다음과 같습니다.
• RAM: 8GB (최저한의), 16GB (추천)
• 저장: SSD
• Processor:
• Intel Core i3 8th Gen (최소 이상)
• AMD Ryzen 3000 (최소 이상)
• Qualcomm Snapdragon 8c (최소 이상)
• Processor Architecture: x64 or ARM64
2. Electronics Tools 에 이미 기본 Windows 버전이 있는지 확인하십시오. 여기서 하세요 ». 기본 버전이 없으면 3단계로 진행합니다.

Made by electrical engineers and hobbyists for electrical engineers and hobbyists, Electronics Tools provides solutions to a wide range of circuit calculations. From the basics (Ohm’s Law) to the more complex (8th order active filters), Electronics Tools has you covered with a clean and straight forward interface that provides the information you need. For instance, suppose you wanted to find the values needed for a simple second order active filter. Entering just the frequency finds the optimum resistor and capacitor values in five tolerance bands and gives you the minimum and maximum corner frequencies for each tolerance. Optionally, you can enter additional values, such as the resistor value, and the remaining values will be calculated. Every calculation provides the information that you need to know when working with your circuits. On smaller screens such as an iPhone, the calculation results can be fully displayed by tapping the “Show” button. The display can also be split showing the data entry area and its schematic along with a scrolling partial view of the results. Electronics Tools includes calculators for: Basic Calculations    Calculator    Capacitance reactance    dB - Voltage    dB - Power    Frequncy-period-wavelength    Inductance reactance    LC resonance    LED series resistor    Ohm's Law    Other Multipliers    Parallel and series capacitor value    Parallel and series inductor value    Parallel and series resistor value    Phase-delta t    RMS-peak-peak to peak Components    FET cheat sheet (Reference)    Resistor Color Code Decoder    Resistor Color Codes Article (Article)    Resistor Value Check    Resistor Value to Color Code    SMD resitor marking to and from value    Standard resistance values (Reference) Conversions    Area    Length    Temperature    Volume Dividers    Dual Supply    Pot with Resistor Dual Supply    Pot with Resistor Ratio    Pot with Resistor Single Supply    Resistor Ratio    Single Supply Filters    2nd Order bandpass    2nd Order bandpass Biquad    2nd Order highpass    2nd Order lowpass    4th Order highpass    4th Order lowpass    6th Order highpass    6th Order lowpass    8th Order highpass    8th Order lowpass    Filter Types (Article)    Highpass RC & RL Amplitude and Phase    Lowpass RC & RL Amplitude and Phase    Passive RC    Passive RL    Power Supply ripple (Full Wave)    Power Supply ripple (Half Wave) Logic    Basic Gates (Reference)    Flip Flop (Reference)    Interfacing Different Logic Families (Article) Op-amp    Differential Amplifier    Inverting Amplifier    Non-inverting Amplifier    Op-amp basics (Article)    Op-amp errors (Article)    Transimpedance Amplifier (Article) Oscillators    555 astable (free running)    555 monostable (one shot)    Logic Gate Oscillator    Sine and Cosine Oscillator Other References    ANSI clearance and tap    Drill Table    Wire Table Voltage Regulators    LM317 - LM338    LM337    Zener Circuit Snippets    Adder Subtractor    Capacitance Multiplier    Constant Current Source    Crystal Oscillator    Op-amp Bridge Drive    Parallel Op-amps    Parallel Transistors    Summing Amplifier    Voltage to Current